Paint Products & Reviews

Sherwin-Williams Emerald Rain Refresh: Specs and Price

Two-story American house with light gray lap siding, white trim and a dark front door during a light rain shower, wet concrete driveway and green lawn in front

Try it on your house

Emerald Rain Refresh on its data sheets: self-cleaning claim, dry time before rain, primer rules, warranty text, list prices and how it differs from Emerald.
5 min read

Emerald Rain Refresh is Sherwin-Williams' exterior acrylic house paint with Self-Cleaning Technology: it is formulated to shed dirt when rain or water touches the wall. It comes in Flat, Satin and Gloss, covers 250 to 300 sq ft per gallon, goes on down to 35°F, is dry to the touch in 2 hours and ready for a second coat in 4 at 45°F and above, and is self-priming on most surfaces (one coat on a repaint, two on bare material). Its lifetime limited warranty covers peeling and blistering. On November 15, 2026, sherwin-williams.com listed it at $139.99 to $145.99 per gallon, $22 more than regular Emerald Exterior. Sherwin-Williams publishes no measurement of how much cleaner the wall stays.

How this page works: every figure comes from the three Emerald Rain Refresh data sheets (March 2026), the warranty text, the Sherwin-Williams catalog and the outside sources listed at the end. Calculations are ours and labeled as such. No paint was applied for this page: where Sherwin-Williams publishes no figure, the page says so.

Preview a paint color on my house

The tool shows a color on a photo of your house. It does not show sheen, dirt or weathering. How it works: our exterior paint visualizer.

Emerald Rain Refresh at a glance: the three data sheets

The product page lists three sheens, two sizes (1 gallon and 5 gallons, no quart) and four bases: Extra White, Deep Base, Ultradeep Base and an Ultra White reserved for the Designer Color Collection. Each sheen has its own sheet: Flat (102.081A), Satin (102.082A) and Gloss (102.083A), all dated 3/2026.

Spec (data sheet)Flat, K47-1900Satin, K48-1900Gloss, K49-1900
Finish0 to 5 units at 85°10 to 20 units at 60°35 to 45 units at 60°
Volume solids41% (plus or minus 2)38%38%
Dry film at 5.3 to 6.4 mils wet2.2 to 2.6 mils2.1 to 2.5 mils2.0 to 2.4 mils
MPI category on the sheet#10#15#11

Try it on your house

  1. 1Your photoPhoto
  2. 2Your colorColor
  3. 3HD render in ~30 sHD render in ~30 s
No photo? Try a sample

Your photo is used only to create your preview. JPG, PNG, HEIC (iPhone)

Common to the three sheets: proprietary acrylic resin, less than 50 g/L of VOC, a shelf life of 36 months unopened, exterior use only, and "Yes" for OTC, SCAQMD and CARB.

The Master Painters Institute lists Emerald Rain Refresh by product code in MPI #10, "Latex, Exterior Flat", MPI #15, "Latex, Exterior, Low Sheen" and MPI #11, "Latex, Exterior Semi-Gloss". One detail for trim: the sheen sold as Gloss sits in MPI's semi-gloss category.

Does Emerald Rain Refresh really work? The claim and its limits

Sherwin-Williams claims the effect and gives no number for it. The product page says the paint is "formulated so dirt washes away upon contact with rain or water". The data sheets list "excellent dirt pick up resistance", "excellent water shedding" and "resistant to wind driven rain". No sheet names a test method, a result or a duration for any of the three.

On the mechanism, the company has said little. In Fine Homebuilding (issue 293, 2020), Rick Watson, presented as Sherwin-Williams' director of product information and technical services, described a "precision-engineered, cross-linking polymer chain that promotes water-beading at the surface" and said the additive is part of the paint itself. Pro Builder (July 2020) reported that the technology came from Loxon Self-Cleaning Acrylic Coating, a masonry product. Our Loxon stucco guide covers that family.

The only comparison shown is in the 2019 product literature: three photos of siding, Rain Refresh clean next to two streaked panels labeled "National Competitor Exterior Premium Product A" and "B", under the line "outperforms conventional exterior paints". It names neither competitor and gives no exposure time and no measurement.

That gap is partly an industry one. A paper in the American Coatings Association's journal, "Towards a Comprehensive Understanding of Dirt Pickup Resistance" (CoatingsTech, June 2020), defines dirt pickup resistance as the ability of a surface to resist discoloration from particles deposited by the environment. Its authors, researchers at Chemours, write that laboratory protocols are "scattered" and that judging this property still depends on outdoor exposure testing. They add that low-VOC latex paints tend to pick up more dirt than solventborne paints. So a buyer has no shared yardstick to compare two cans on this point.

Three limits follow from the wording itself (our reading):

  • It needs water on the wall. The claim is about dirt that washes away "upon contact with rain or water". A wall under a deep porch roof that rain never reaches has to be rinsed with a hose.
  • Dirt is not mildew. The sheet treats mildew apart: "a fungus that looks like dirt but won't wash off", to be removed before painting. Its mildew line ("contains agents which inhibit the growth of mildew on the surface of this coating film") is word for word the one on the regular Emerald Exterior sheet. The self-cleaning claim adds nothing on mildew or algae.
  • Stains from below are a primer matter. Tannin from cedar, wax from hardboard or rust from steel are handled by the primer rules further down, not by rain.

On reviews: on November 15, 2026, the Sherwin-Williams exterior paint list displayed 3.6 stars out of 5 from 30 customer reviews for Emerald Rain Refresh, and 4.3 from 76 for Emerald Exterior. Thirty self-selected reviews are a small sample. We report the figure as displayed and add no rating of our own.

Emerald Exterior vs Emerald Rain Refresh: the differences on paper

The regular Emerald Exterior sheets (Flat, Satin, Gloss, 03/2026) share most of their text with the Rain Refresh sheets. We compare specifications, not performance.

Spec (data sheets, 3/2026)Emerald Rain RefreshEmerald Exterior
Resin as printedProprietary acrylic100% acrylic, "patented cross-linking" technology
Dirt and water claimsSelf-cleaning, excellent dirt pick up resistance, excellent water shedding, resistant to wind driven rainResistant to blistering, peeling and dirt pick-up
Touch dry at 45°F and above2 hours1 hour
Touch dry at 35 to 45°F4 hours2 hours
Recoat4 hours; 24 to 48 hours at 35 to 45°FSame
"Ready for service overnight"Not on the sheetOn the sheet
Volume solids, Flat / Satin / Gloss41% / 38% / 38%43% / 39% / 38%
Coverage, minimum temperature, VOC, gloss ranges, MPI numbers250 to 300 sq ft/gal, 35°F, under 50 g/L, #10 / #15 / #11Same
WarrantyLifetime limited, peeling or blisteringSame text, word for word
List price per gallon, Flat to Gloss (Nov 15, 2026)$139.99 to $145.99$117.99 to $123.99

In short: Rain Refresh adds three claims, takes twice as long to dry to the touch, carries slightly less solids in Flat and Satin, and lists $22 higher. The Emerald Exterior page also offers a fifth base, High Reflective White.

For the Emerald range as a whole, see our Emerald Exterior review. For the tiers below: our SuperPaint vs Duration vs Emerald comparison, and our pages on Duration Exterior and Latitude.

Dry time, recoat and rain: what the sheet says

At 50% relative humidity35 to 45°F45°F and above
Dry to the touch4 hours2 hours
Recoat24 to 48 hours4 hours

These times depend on temperature, humidity and film thickness, the sheet adds. Its weather rules:

  • Rain. "Avoid using if rain or snow is expected within 2-3 hours." That is the only figure given. The sheet states no time after which the film is rain-resistant, no full cure time and no wait before washing.
  • Cold. Not below 35°F, and not when air or surface temperature may fall below 35°F within 48 hours. At 35°F air temperature, the sheet warns, the wall may be colder.
  • Dew. Air, surface and paint must be at least 5°F above the dew point. The National Weather Service defines the dew point as the temperature to which air must be cooled to reach 100% relative humidity.
  • Sun and metal. "Do not paint in direct sun." On large expanses of metal siding, air, surface and paint must be at 50°F or more. Our aluminum siding painting guide covers that job.
  • Tape. The sheet asks for a high bond exterior painter's tape and a 24-hour dry before any tape is applied to the new coating.

On a door that has to close the same evening, 2 hours to the touch is slow next to a dedicated enamel. Our SnapDry door and trim comparison sets those times side by side.

Close-up of gray-blue painted lap siding with rain water beading into droplets and running down the boards, a white corner trim board on the right
Water beading on painted siding: the data sheets claim water shedding and dirt pick up resistance for Rain Refresh, and print no figure for either.

Surfaces and primer: what "self-priming" covers

The sheet explains the term: on many bare surfaces, "the first coat of Emerald Rain Refresh acts like a coat of primer and the second coat provides the final appearance and performance". Hence two coats on new, bare surfaces and one on a repaint, where bare spots are first spot-primed with Rain Refresh itself. The sheet then lists a system for each surface:

SurfaceSystem on the Rain Refresh sheet
Aluminum, aluminum siding, galvanized steel2 coats, no primer, once corrosion is removed.
Vinyl siding2 coats, plus a white primer "if needed". Color rule below.
Wood, including cedar and redwood2 coats. Tannin staining "will be trapped in the first coat". If it persists, spot prime with Exterior Oil-Based Wood Primer.
Hardboard (wood composition board)1 coat of Exterior Oil-Based Wood Primer first (wax bleed).
Brick, stucco, cement, concrete, cement composition siding and panelsLoxon Concrete & Masonry Primer or Loxon Conditioner "if needed", then 2 coats.
Concrete block, split face block1 coat of Loxon Acrylic Block Surfacer, then 2 coats.
Steel1 coat of All Surface Latex Enamel Primer, then 2 coats.
  • When masonry needs the primer. Any surface with a pH above 9 must be primed with a high pH-resistant coating. New masonry and stucco cure about 30 days, or 7 days with Loxon Concrete & Masonry Primer. Powdery old masonry is sealed with Loxon Conditioner.
  • Primers in the cold. "Standard latex primers cannot be used below 50°F": check the primer's own label. Our ProBlock primer guide shows which Sherwin-Williams primers go lower.
  • Vinyl. Do not paint vinyl a color darker than the original or with a Light Reflective Value under 56 unless it is a VinylSafe color, or the vinyl may warp. The sheet counts 100 VinylSafe options, and the VinylSafe page names Rain Refresh among the paints they can be mixed in. See our vinyl siding painting cost guide.
  • Lead. The preparation section opens with a lead warning. EPA's lead-safe guidance for DIYers says a home built before 1978 may have lead-based paint. Read it before scraping, with our guide to lead paint testing in pre-1978 homes.

Tools, coats and how much to buy

Tools on the sheet: a nylon-polyester brush (see our exterior brush guide), a polyester roller cover, or an airless sprayer at 2,000 psi with a 0.015 to 0.019 inch tip. No thinning: "No reduction needed."

Coverage is 250 to 300 sq ft per gallon at 5.3 to 6.4 mils wet. By our calculation that is the geometry of the film, with nothing lost to the roller or a rough surface: rough stucco or rough-sawn cedar will take more.

Our calculation for 1,500 sq ft of wall: 5 to 6 gallons for one coat on a repaint, 10 to 12 gallons for two coats on bare or new surfaces. For 2,000 sq ft: 6.7 to 8 gallons, or 13.3 to 16.

Emerald Rain Refresh price: list prices on November 15, 2026

These are the list prices displayed on sherwin-williams.com on November 15, 2026, without sign-in and with no store selected: per-gallon ranges on the exterior paint list, each sheen and size on the product page (Extra White base). The site says prices are for U.S. Sherwin-Williams locations, exclude taxes, and are to be confirmed after sign-in. Your store may charge a different amount.

Emerald Rain Refresh, Extra White (list price, Nov 15, 2026)1 gallon5 gallons
Flat$139.99$694.95 ($138.99 per gallon)
Satin$142.99$709.95 ($141.99 per gallon)
Gloss$145.99$724.95 ($144.99 per gallon)

So the range on the list page is the sheen: each step up adds $3 a gallon. The 5-gallon pail saves $1 a gallon. At the sheet's coverage, Flat works out to 47 to 56 cents per sq ft per coat (our calculation). Sale and account prices are not public figures, so none are given here.

Why is Emerald Rain Refresh so expensive?

Sherwin-Williams does not publish a reason for the price. Its catalog shows the position: on the list page that day, Rain Refresh carried the highest list price of these six house-paint lines.

Exterior lineList price per gallon (sherwin-williams.com, Nov 15, 2026)
A-100 Exterior$67.49 to $73.49
SuperPaint Exterior$86.99 to $94.99
Latitude Exterior$103.99 to $109.99
Duration Exterior$111.49 to $117.49
Emerald Exterior$117.99 to $123.99
Emerald Rain Refresh$139.99 to $145.99

The step from Emerald Exterior is $22 a gallon in each sheen, and $110 on a 5-gallon pail of Flat ($694.95 against $584.95). On 1,500 sq ft of bare wall, two coats (10 to 12 gallons), that is $1,390 to $1,670 in Rain Refresh Flat against $1,170 to $1,406 in Emerald Exterior Flat: $220 to $264 more (our calculation, pails first, then single gallons). On paper, that difference buys the three claims in the comparison table: warranty, coverage and recoat times are identical.

The price has moved since launch. In April 2020, the Journal of Light Construction reported a list price of about $522 for five gallons. The same size lists at $694.95 to $724.95 today, 33% to 39% more (our calculation). For the cheaper end of the range, see our A-100 exterior guide.

How long does Emerald Rain Refresh last?

Sherwin-Williams does not publish a service life in years for Emerald Rain Refresh, and no Sherwin-Williams document read for this page gives a duration for the self-cleaning effect. Two things are in writing. The data sheet gives a shelf life of 36 months for an unopened can. And the Lifetime Limited Warranty (dated 7/9/2021) sets out what the company stands behind:

  • What it covers. The paint peeling or blistering "during the lifetime of the purchaser", when applied according to the instructions on a properly prepared exterior surface.
  • The remedy. With proof of purchase, at the store where it was bought: replacement paint for the repair, or a refund of the purchase price. "This is your sole remedy."
  • What it excludes. Labor, consequential damages, and any defect from improper surface preparation, structural defects, failure of a previous paint or improper application.
  • Who holds it. "The original residential consumer paint purchaser". It is not transferable to the next owner.
  • What it does not mention. Fading, chalking, dirt, mildew and the self-cleaning effect appear nowhere in the text.

Keep the receipt and a record of the preparation.

When Rain Refresh fits the documents, and when it does not

  • Fits: walls that rain actually reaches, on a house where dirt is the complaint, near a road or a field. The ACA paper names soot as the dominant discoloring agent on light-colored surfaces: a pale wall is where the claim has the most to prove.
  • Does not fit: a porch ceiling or a wall under deep eaves bought for the self-cleaning effect. No rain, no rinse.
  • Does not fit: a mildew problem. The sheet says the same about mildew as regular Emerald's.
  • Does not fit: a house you will sell soon, if the lifetime warranty is the reason to pay more. It stays with the original purchaser.
  • Weigh it: regular Emerald Exterior has the same coverage, recoat time and warranty on paper for $22 less a gallon.

Before the paint line, the color

Rain Refresh is tinted in the store: its sheets read "Color: Most Colors" and list four tint bases. A dirt-shedding paint does not fix a color that looks wrong. Our Sherwin-Williams exterior paint guide compares the lines, and our guide to choosing an exterior house color covers the decision.

Settle the color before you order the gallons

Upload a photo of your house and try colors on the siding, trim and front door. The preview shows color only, not sheen or weathering.

Try colors on my house

Sources and references

Frequently asked questions

Does Emerald Rain Refresh really work?
Sherwin-Williams states that Emerald Rain Refresh is formulated to be self-cleaning by shedding dirt upon rain or water contact, and its data sheets list excellent dirt pick up resistance and excellent water shedding. The company publishes no test method, figure or duration for that effect. The claim concerns dirt on walls that rain or a hose reaches. It is not a mildew claim: the sheet asks for mildew to be removed before painting.
How long does Emerald Rain Refresh last?
Sherwin-Williams does not publish a service life in years for Emerald Rain Refresh, nor a duration for the self-cleaning effect. Its Lifetime Limited Warranty covers peeling or blistering during the lifetime of the original purchaser, when the paint is applied as instructed on a properly prepared surface. The remedy is replacement paint or a refund of the purchase price. Labor is excluded and the warranty is not transferable.
What is the difference between Emerald Exterior and Emerald Rain Refresh?
On their March 2026 data sheets, both cover 250 to 300 sq ft per gallon, recoat in 4 hours at 45°F and above, apply down to 35°F and carry the same lifetime limited warranty text. Rain Refresh adds the self-cleaning, water shedding and wind-driven rain claims, uses a resin described as proprietary acrylic, and takes 2 hours to dry to the touch instead of 1. On November 15, 2026, its list price was $22 per gallon higher in each sheen.
How much does Emerald Rain Refresh cost per gallon and per 5 gallons?
On November 15, 2026, sherwin-williams.com displayed these list prices without sign-in for the Extra White base: Flat $139.99 per gallon and $694.95 for 5 gallons, Satin $142.99 and $709.95, Gloss $145.99 and $724.95. Regular Emerald Exterior listed at $117.99 to $123.99 per gallon. The site asks you to sign in to confirm pricing, and your store may charge a different amount.
How long does Emerald Rain Refresh need to dry before rain?
The data sheet says to avoid using it if rain or snow is expected within 2 to 3 hours. At 50% relative humidity it is dry to the touch in 2 hours and can be recoated in 4 hours at 45°F and above. Between 35 and 45°F, touch dry takes 4 hours and recoat 24 to 48 hours. The sheet gives no full cure time.
Does Emerald Rain Refresh need a primer?
It is self-priming on most surfaces: one coat on a repaint and two coats on new, bare surfaces, the first acting as the primer. The data sheet still asks for a primer in specific cases: a high pH-resistant primer on masonry above pH 9, Exterior Oil-Based Wood Primer on hardboard and on cedar or redwood where tannin staining persists, a block surfacer on concrete block and a metal primer on steel.
Can Emerald Rain Refresh be used on vinyl siding?
Yes. The data sheet lists vinyl siding with two coats, after a wash and, if needed, a white primer. It adds a color rule: do not paint vinyl a color darker than the original or with a Light Reflective Value below 56 unless it is a VinylSafe color, because the vinyl may warp. Sherwin-Williams lists Emerald Rain Refresh among the paints its VinylSafe colors can be mixed in.
What sheens does Emerald Rain Refresh come in?
Three: Flat (0 to 5 gloss units at 85°), Satin (10 to 20 units at 60°) and Gloss (35 to 45 units at 60°). The Master Painters Institute lists them in its categories #10, #15 and #11, the last being its exterior semi-gloss category. Sizes are 1 gallon and 5 gallons.

Trademarks mentioned (Sherwin-Williams, Benjamin Moore, Behr, Caparol, Brillux, Sto, Alpina, Valspar, PPG, Glidden, Dulux, Crown Trade, Sandtex, Farrow & Ball, Johnstone's, Leyland) are property of their respective owners. FacadeColorizer is independent and not affiliated with any of them. Nominative fair use under Lanham Act §1125.

Share this article with your neighborhood:

Related articles and color guides

Ready to customize your home color?

Color visualizer

Try it on YOUR photos - customize your home color

Stop guessing. Our AI analyzes your photo and renders a photorealistic color preview in 30 seconds - optimized for American homes, neighborhoods and ZIP code-level light conditions.

Start a free color simulation